Known methods to access home Fonera via SSH , they can be complicated for those who are not as hands (in this case a server) at the time of "manufactured" a circuit of several interconnected electronic elements.
The designers fonera apparently already taken into account the possibility that users could "customize" through the serial port that is in the bowels of "social router", but the difficulty of the process means that not many users were going to make life difficult in these matters.
In its day, and updated the firmware of the router directly to the officer zyxel prestige 660HW through a method similar to the fonera.
The process is summarized in 2 steps:
1) Remove the cable end which is the cell phone connector (pinout) and locate the corresponding wires (TX, RX and GND).
2) Cut a piece of audio cable to the connector and make the connection with 3 wires so that the audio connector pins make correspondence with the serial port RX, TX and GND. (Yes, I do not need Alimet the circuit from the fonera because it feeds on itself from the serial port!)
In my case I have done with a generic cable c25-c45 Siemens mobile, but as we see it cables can be done with other models Mobile:
Truly all this work it did in its day piolinso (of adslayuda.com forums) with the help of all collaborators who helped to increase the database experimenting with all sorts of cables and mobile.
The purpose of this is that the user can have all the tools to customize your fonera accessing through SSH Operwrt minimizing the time required with the previous circuit manufacturing process and the cost of purchasing euro all components.
In summary
Difficulty
Customize fonera = Time + Money
desorradores Simple formula that La Fonera could take into account when design reduces the number of users who would end "customizing"
The difficulty with this method reduces to notablemento circuit method if we consider that under normal conditions at home nobody has a "chip max232, condensers, welder ... But more than you have at home out there at the bottom of a drawer mobile cable used in your day to free your mobile device and turn up logos, ditties ... and scissors (or alternatively the knife to cut the ham).
price of these cables in the event that is not available one can easily get looking around (I have seen x 3 €), otherwise it could borrow from someone you know that you know cable has a phone that you no longer use and do not need cable at all.
Notes to consider:
Here we will discuss the cables have been tested and work properly. If need be highlighted v 3.3 La Fonera or only RX, TX and GND.
Siemens C25 and assumes A / C / S / M / SL 2x, 3x, 4x and 50 (Generics and Originals) (No, only RX, TX and GND) Tested by (Piolinso)
Siemens S55 Siemens assumes and A52, A55, A56, A60, C55, C56, C60, C65, CF62, CT56, M55, MC60 , MT55, S55, S56, S57, S65, SL5C, SL55, SL56, 2218, SX1
If the cable in question Siemens Original: (+3.3 v If you need the part of the RX, TX and GND) Tested by (robermad1986)
If it is a generic cable: (No, only RX, TX and GND) Tested by (Tobel)
Ericsson T10 and assumes 6xx and 7xx ( Generics and Originals) (If you need a +3.3 V to part of the RX, TX and GND) Tested by (snow peas)
T2X Ericcson and assumes T3X, T6X, A26XX, Rxxx, P800 (Generic and probably original) (If you need the +3.3 V of the RX, TX and GND)
Alcatel 50x / 51x and assume that B1-B5, DB, 30x, 50x and 70x (No, only RX, TX and GND) Tested by (Currin)
Siemens C60 USB Cable (emulating an RS232 port) (N , Tx, Rx and GND) mobile action ma-8720p model and GND pins are pin 2, pin 3 Tx and Rx pin 4. Tested by (Mbaza)
